How to wire a light socket with ground

how to wire a light socket with ground

How to Wire a Porcelain Light Fixture Socket

Feb 05,  · Mark Donovan of likeloveen.com shows how to properly and safely wire an electrical light socket so that the threat of electrocution while in. How to Wire a Grounded Lamp Socket 1. Unplug the lamp. Remove the light bulb and lamp shade. Remove the lamp shade harp. 2. Remove the top half of the lamp socket cover by either pressing your thumb on the area marked "press" or inserting a 3. Remove the socket insulation cover. Pull the .

Home » DIY » Connect a 2-wire light fixture without ground. How much does it cost to make a billboard turn off the power at the breaker or fuse box before you work on electricity. This keeps you safe from potential electric shock. The ground wire is designed to protect you.

In the event that the live wire comes loose and touches the light fixture, the ground wire diverts the power and blows the breaker, instead of you feeling an electrical shock when you touch the fixture. The light works just fine without fround, just like in the case of a light switch. But before you just discard it entirely, there may be an alternative way to hook it up. Just leave it disconnected in that case. Assuming the electrical box is metal, take a look at the box.

Frequently the metal box itself is grounded. If the Romex wire coming into the box appears to have a metalized surface, that surface probably serves as a ground. If not, look for how to wire a light socket with ground screw hole in the box. You can put a short machine screw in the hole, then connect the ground wire to that screw. Putting a screw in an electrical box can be a pain. I find a magnetized screwdriver helps. Remove one of the long screws that holds the fixture in place.

Thread an nut onto the screw. Replace the screw. Wrap the wire around the screw, then cinch the nut down to hold it. What if you find a plastic box with no ground? You can wrap the grounf around one of the screws that holds the fixture on, grlund the only purpose it serves sockdt to help hold the fixture up while you wire the black hot and white common wires.

Never, ever, EVER connect the ground wire to the white wire. That defeats the purpose. Safety first Most light fixtures have three wires, including a bare or how to wire a light socket with ground green ground wire.

The purpose of the ground wire The ground wire is designed to protect you. Examine the metal box Assuming the electrical box is metal, take a look at the box. A plastic box with no ground What if you find a plastic box with no ground? If you liked this post, please share it! Like this: Like Loading Related stories by Dave Farquhar.

Safety first

Jun 21,  · Lamp socket outlet: Connect hot and neutral wires correctly. If you wonder why you have to identify and connect the hot and neutral wires correctly in a lamp, read on. True, the lamp will usually work either way. But the issue is safety. Normally, power (voltage) comes through the tab on the socket base. The threaded socket is the neutral. Bend the exposed end of the ground (green) wire to a degree angle. Insert the ground (green) wire through the top opening of the cap. Insert the exposed section of the green (ground) wire into the ground terminal opening under the screw. Make sure the exposed copper wire is completely inside the . Typically the ground wire is attached to the metal housing of the light fixture. The ground wire connection should provide a continuous bond throughout the metal components of the light fixture. In some cases, the ground wire extends through out the light fixture to junction box locations where the light socket wiring is spliced together.

Last Updated: October 2, References. To create this article, 16 people, some anonymous, worked to edit and improve it over time. There are 14 references cited in this article, which can be found at the bottom of the page. This article has been viewed , times.

Learn more Trying to wire a light in your home can be intimidating. After all, wiring involves electricity, and electricity can be dangerous. However, by taking basic precautions and understanding the basic working of a circuit and the wires involved, you can have new fixtures wired and installed in your home in no time! Next, twist together like-colored wires coming from the fixture and the wall or ceiling, such as black with black and red with red, then screw a wiring cap over the exposed ends.

Then, tighten the screw, fasten the fixture to the mounting hardware, and test your new light. For tips on how to remove your old light, keep reading!

Did this summary help you? Yes No. Log in Social login does not work in incognito and private browsers. Please log in with your username or email to continue. No account yet? Create an account. Edit this Article. We use cookies to make wikiHow great. By using our site, you agree to our cookie policy. Cookie Settings. Learn why people trust wikiHow. Download Article Explore this Article parts. Tips and Warnings. Things You'll Need. Related Articles.

Article Summary. Part 1 of Cut power to your circuit. The best way to do this is by turning off the electricity supplied to the circuit on which you will be working at the junction box also called a fuse box for your home. Switch the breaker of your fuse-box so the fuse for the circuit supplying electricity to your fixture reads "Off.

Flick the light on, and if the circuit has been disabled, the light should stay off. Clean the old fixture and installation area. If the light you are wiring is in the ceiling, you should clean any cobwebs and dust before attempting to install your new fixture. The same is true for lights or switches in walls; a clean work area will improve your ease of installation. If you are using a ladder to reach your light fixture, or are in a less than ideal position, be sure the ground is also clear of debris or anything else that might affect your balance or safety.

Remove the old fixture covering. There is usually, but not always, a decorative globe, shield, or some kind of external feature covering your existing light fixture. This could also be something more involved, like ceiling fan blades.

Unmount the fixture. There will be a mounting bracket holding your old fixture in place. You will need to unscrew this from mounting bracket, usually with Phillips-head screwdriver, and then pull it from the bracket.

Be sure you support the old fixture with your hand as you unscrew it from the mount. If you do not support the fixture, it could fall to the floor once you loosen the screws holding it in. Lower the fixture. Allow the unscrewed fixture you are supporting with your hand to descend a few inches below its mount. You will likely see three wires attached to your fixture: a hot wire, grounding wire, and neutral wire. You will need to use your free hand to uncouple these wires, twisting the wiring cap to free the wires from each other.

Hot wires are those that run electricity to your fixtures and grounding wires are intended to offer surge electricity a neutral point, like the earth, into which it can dissipate. This is fairly common in new light fixtures.

Disengage your light from its wires. You should see plastic caps, called wiring caps also called a wire nut , with two wires running into each cap. One wire will come from the light, the other from the main electrical circuit of your house.

Disengage the wires by twisting the wiring cap until it comes free. Part 2 of Check for compatibility. In most cases, the mounting hardware for your new fixture will fit the bracket that's already installed. You'll need to hold the new light fixture up to the existing mounting bracket and compare fasteners and size to make sure you don't need to install a new mounting bracket.

Swap in a new bracket, if necessary. Oftentimes, if a light requires a special bracket, this will be included with the light you have bought. If not, you can look up the light information online by doing a general search of the name of the light fixture, which you can find on the box. Listed with its information should be mounting information as well. Once you know the kind of bracket you need, you can find and purchase it at your local hardware store.

Replacing the old bracket is just a matter of unscrewing it and screwing the new one into place. Investigate the age of your wiring. This is especially important if you have an older home, in particular, any home built before Wiring installed prior to has weaker insulation than contemporary circuits, meaning the heat generated by your fixture could cause a short, fire, or worse.

Join like colored wires. Depending on your country, the colors that code which wires are live, ground, and neutral may differ. In any case, you should support your new light with one hand and take each like colored wire coming from your wall or ceiling and combine it with its mate coming from the light fixture. Twist the exposed ends of the wire together, and seal it by screwing on a wiring cap. Ground your fixture. If there is a remaining wire that is green, green and yellow, or bare copper, you should screw it into place on the mounting hardware for your light fixture.

There will likely be a small screw for this purpose on the fixture, which you can unscrew slightly, slot the wire into the gap between screw and fixture, and then tighten to fasten your ground.

Many metal surfaces can be suitable for this purpose. Fasten your fixture in the mounting bracket. Continuing to support your fixture with your hand, hold it in place so as to line up the screw holes with those of the bracket and screw it into the mount using the hardware that came with the fixture. Finish any supplemental installation. There may be external features or parts, like a light cover or ceiling fan blades, to add to your new light fixture. Take a moment to step back and inspect your fixture for levelness, orientation, and flushness with the surface on which you've installed it.

Some light fixtures are permanently angled a certain way, and improper installation can lead to your light shining where it does little good. Test your new light. Return to your fuse-box and reset the fuse for the room in which you've been wiring to restore the flow of electricity to the room. Now you can install a light bulb and turn on the new light fixture you have installed to test it out.

Part 3 of Test for electrical current. Sometimes, over the course of installation, a wire might be jostled or damaged in such a way as to compromise its ability to transmit electricity to your new light. Additionally, in some cases, contractors may have used different colored wires for your electrical setup. In both of these cases you should use a circuit tester to ensure you don't make a dangerous mistake with your wiring.

A circuit tester can be purchased at most hardware stores. Turn off the electricity, free the wire you are uncertain about from the old fixture, and then turn the electricity back on, being sure that your free wire is not touching anything dangerous. Your circuit tester will have two nodes; connect one to the questionable wire and the other to a grounded, metal surface or your ground wire.

If the light on your tester turns on, the wire is hot and is supplied with electricity. Create space to work. Some wiring jobs are done haphazardly, with poorly managed wire in the fixture box or wall or ceiling where you are working. After turning off the circuit, hold up your fixture to your mount to approximate how much wire you will need. Be sure to leave some excess. Wire can become damaged or get brittle over time, in which case, you might want to strip some insulation off the wire to tie a new fixture in to your circuit.

Give yourself more wire.

0 thoughts on “How to wire a light socket with ground

Add a comment

Your email will not be published. Required fields are marked *