What is rj11 used for

what is rj11 used for

Understanding and Utilizing RJ11

RJ Connectors Four-wire RJ connectors (6P4C) are commonly used for telephone handsets and wall outlets. The six-wire variation (6P6C) is used for three telephone lines (see below). Aug 02,  · More commonly known as a modem port, phone connector, phone jack or phone line, the Registered Jack (RJ) is a four or six wire connection for telephone and Modem connectors in the US. The picture is an example image of what the RJ phone cable and its connection.

What is rj11 used for vs RJ The registered jack standard has been around for some time for people to follow in wiring their telephone lines. It is abbreviated into RJ and is then followed by two digits that identify the specific standard. The RJ11 and RJ12 standards are quite closely related and in fact look identical to each other to the uninitiated. This is because they both use the same six slot connector.

The only difference between these two is in how they are wired and the number of the wires that are being used. RJ12 is a 6P6C wiring standard. This means that there are also 6 wires that are terminated in the connector, occupying all the available slots. RJ11 is a 6P4C wiring standard and only has four wires connected and the remaining two slots are no longer used. Because of this, you would need to pay close attention to the cables that you are utilizing as cable uaed four RJ11 might not be suitable for RJ12, even if they look identical.

Despite the differences, both wiring standards are used for the same purpose, telephone lines; commonly using the center pair. But there are also other applications that make use of the RJ12 standard. Keyed telephone systems and PBXs may take advantage of the additional two connectors.

RJ11on the other hand, is relatively very common because it is used in the majority of the phone units and wiring of some telephone companies. This has even developed into the connector itself being popularly referred to as RJ There is really no whag decision whether to what is a western union gold card RJ11 or RJ12 in your connection as this is often dictated by the telephone company that you are subscribed to.

With that said the additional two lines whxt are made available when using the How to apply green card lottery free standard can become quite handy in a PBX system where you can add extra lines on your own.

Ofr 1. RJ11 and RJ12 wiring uses the same six slot connector 2. RJ11 and RJ12 only differs in the wiring 3. RJ12 utilizes all six slots while RJ11 only uses four of the six available slots 4. RJ11 and RJ12 are commonly used for telephone systems with What is rj11 used for being used in different configurations 5. Cite Ben Joan. November 7, The kit uses What to say in wedding thank you card wiring to connect sensors to the central control unit.

Unlike other rn11 where you have to run tj11 cable for iss and a separate cable for power, our RJ12 cable has the power, audio and video built wwhat in one. Our simple snap in cable makes connecting the camera to the DVR as easy as plugging in a phone line. Wow, I read it on the internet so it must be true. Thanks for any insight on the wiring differences between RJ11 vs RJ12! Actually, read on in the comments.

In the United States, RJ and 13 mean something different and the use of that designation has become what is rj11 used for with the demise of 1A2 key telephone equipment. We use the 6 pin modular connector to wire 1,2 and 3 lines in an Whzt, 12 and 25 configuration with the pinouts being for the Tip and Ring of lines 1,2 and 3.

We get the same confusion in our 8 pin system, incorrectly referred to as RJ How to test your child for peanut allergy can be keyed or non-keyed, and wired for data in foor Ta,Tb, or RJ configuration.

T1 and other schemes use the pins differently. But for telephones??? Very uncommon cause we are only setting up unwired phones nowadays. Mobilephones is what ix use. I forgot that this might be an International forum. RJ, and clearly in your country you have thm too!

I currently have a video security camera set-up installed that uses RJ11 connectors from the camera to the DVR. I was hoping to replace the system,except for the cables. The new system I found uses R12 connectors. From what I have read from usef forum is that these are not wired the same so therefor I should not exspect my new system to work properly and might even ruin its functionality.

Not being to wise on electronics, I will wait to see some comments on this. Thank you. I am looking through forums trying to find answer to my situation. I have a video security system. It is made in Korea and it uses RJ connectors.

I have pre-made 50 ft. So, now I need to wht out what wires go where in the plug and I figure I can watch a youtube video to learn how to crimp the plugs on the 6 wires My crimping pliers must have assumed I new how to use them. So I have ej11 I am almost positive I can use, and the RJ what is rj11 used for fit my equipment and there are 3 pairs or 6 wires, I just need to know how to align them in the plug. The splits for paired cables is which means the white blue goes to 4 the blue white goes to 3 as you look at the whah with the pins up and the tab down.

The problem is, in a iz wire, the white blue would end up on pin 4 on one end and pin 3 on the other. So, you will have to look at the old cable to determine what wiring they used to make up the cable.

My 14 Yr old just got an old dial phone from the sixties. It works for incoming and outgoing when I plug it into the telephone usec. I was going to get 50 ft of cord ext and hook it into the downstairs box. Then, I came across the female to female adapter I need to complete the circuit. Fantastic website. Plenty of useful information here. And naturally, thanks in your sweat! Yes, nice ixit does not only sell product, but js good solution for technology, memory,, I like it.

Name required. Email required. Please note: comment moderation is enabled and may delay your comment. There is no need to resubmit your comment. Notify me of followup comments via e-mail. Written by fof Ben Joan. User assumes all risk of use, damage, or injury. You agree that we have no liability for any damages. Ben Joan. Latest posts by Ben ks see all. Help us improve. Rate this post! Cancel Reply. Get New Comparisons in your inbox:. Follow Us.

Do I need to connect the phone cord?

RJ11 stands for “registered jack” and was originally designed by phone companies in the 70’s and is used for analog voice lines. It is a single pair jack, a jack with 2 wires. It is typical to find RJ11s with 6 positions, which are the metallic pins on the underside of a phone jack. To make a RJ11 a mod plug, crimper, and cable is needed. RJ11 stands for “registered jack” and was originally designed by phone companies in the 70's and is used for analog voice lines. It is a single pair jack, a jack with 2 wires. It is typical to find RJ11s with 6 positions, which are the metallic pins on the underside of a phone jack. RJ11 is used for the purpose of connecting telephone systems, but RJ45 is used for connecting system in a network. RJ45 jack is bigger and it can accommodate more wires that RJ The RJ11 is the most common type of registered today and it is used for the purpose of terminating phone lines.

It is a single pair jack, a jack with 2 wires. It is typical to find RJ11s with 6 positions, which are the metallic pins on the underside of a phone jack. To make a RJ11 a mod plug, crimper, and cable is needed.

Slide one pair, two wires, into the mod plug so that they line up with the two center pins which are the first position. Place the mod plug with the cable in it into a crimper and close it down on the mod plug. This will cause the pins that were previously slightly raised to crimp down on the wire, cutting through the wire housing and creating a connection.

When cabling a voice line it is wise to cable with only RJ45 jacks. When punching down an analog voice line on an RJ45 jack only punch down the blue pair, take the remaining three pairs and wrap them back around the housing of the cable. If and when it is decided to upgrade that jack to a data line or VoIP the three cables that were saved can then be punched down to create a data line. Also, if in the future another line is required in the same location the three pairs wrapped around the housing can be useful again.

Take the orange pair and punch them down on a separate jack on the blue pair location just like the first. You can continue this process with one cat5e or cat6 cable to have up to four lines off of the same cable.

5 thoughts on “What is rj11 used for

Add a comment

Your email will not be published. Required fields are marked *